{"product_id":"xprite-h7-canbus-decoder-harness-pack-of-2-anti-flicker-error-free-plug-and-play","title":"Xprite H7 Canbus Decoder Harness Pack of 2 — Anti-Flicker, Error-Free Plug-and-Play","description":"\u003cp\u003e\u003cstrong\u003eXprite H7 Canbus Decoder Anti-Flicker Harness provides plug-and-play suppression for flicker, OBC errors, and radio interference when fitting H7 LED bulbs.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eSwapping factory halogen or older bulbs for bright H7 LED lamps can trigger dashboard warnings, flickering, or radio noise on many vehicles. The Xprite Reflex Series Canbus decoder is an inline accessory designed to address those electrical and communication irregularities so your LED upgrade behaves like an OEM fitment. Built with a heavy-duty casing and an error-free resistor-capacitor layout, this harness helps stabilize current and signal feedback to the vehicle’s onboard systems.\u003c\/p\u003e\n\n\u003ch3\u003eHow does this harness stop flickering and dashboard errors?\u003c\/h3\u003e\n\n\u003cp\u003eThe harness uses a resistor-and-capacitor circuit tuned for H7 LED loads to prevent rapid brightness changes and false warnings. It conditions the power draw and cleans up the signal the vehicle’s computer monitors, reducing flicker and clearing OBC lamp fault messages in most cases.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eError-free design with combined resistor and capacitor components\u003c\/li\u003e\n  \u003cli\u003eStabilizes current flow to eliminate rapid dimming or flashing\u003c\/li\u003e\n  \u003cli\u003eReduces false CAN bus or OBC fault codes caused by low-load LEDs\u003c\/li\u003e\n  \u003cli\u003eHeavy-duty housing improves heat dissipation for durable operation\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWill the Xprite decoder fit my vehicle and H7 bulbs?\u003c\/h3\u003e\n\n\u003cp\u003eIt’s built for H7 plug connections and intended to work with LED headlight and fog light conversions, not HID systems. While the unit is plug-and-play on many vehicles, always verify clearance inside tight housings and check compatibility with your car’s electrical system before installation.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eDesigned specifically for H7 LED bulb plugs\u003c\/li\u003e\n  \u003cli\u003eNot compatible with HID ballast systems\u003c\/li\u003e\n  \u003cli\u003ePack of two decoders for both sides of the vehicle\u003c\/li\u003e\n  \u003cli\u003eConfirm physical dimensions and plug type for tight headlight assemblies\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow easy is installation and what tools are needed?\u003c\/h3\u003e\n\n\u0026gt; \u003cp\u003eInstallation is straightforward for most users: the decoder connects inline between the vehicle harness and the H7 LED bulb plug with no soldering required. It’s an all-in-one unit meant for direct replacement, though you may need basic tools to access the headlight housing depending on your vehicle’s assembly.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eSimple plug-and-play inline connection — no splicing required\u003c\/li\u003e\n  \u003cli\u003eMay require removing headlight housing or trim for access\u003c\/li\u003e\n  \u003cli\u003eTypical install tools: screwdriver or trim tool for panel removal\u003c\/li\u003e\n  \u003cli\u003eFollow safety steps: disconnect battery if recommended by vehicle maker\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat performance improvements can I expect after fitting this harness?\u003c\/h3\u003e\n\n\u003cp\u003eWhen paired with compatible H7 LEDs, the decoder reduces radio interference, prevents headlights from extinguishing when the engine starts, and minimizes dashboard lamp warnings. It’s an accessory that corrects common electrical issues encountered during LED retrofits without altering the bulb itself.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eReduces flicker and prevents lights going out on engine start\u003c\/li\u003e\n  \u003cli\u003eMinimizes radio and electrical interference from LED loads\u003c\/li\u003e\n  \u003cli\u003eHelps clear false OBC or CAN bus error messages in many vehicles\u003c\/li\u003e\n  \u003cli\u003eDurable construction for consistent long-term performance\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho this is for: the Xprite H7 Canbus Decoder Anti-Flicker Harness is aimed at drivers upgrading to H7 LED headlight or fog bulbs who experience flickering, false error codes, or interference after the retrofit. It’s ideal for DIY installers and professional shops seeking a compact, plug-in solution to stabilize LED electrical behavior. Remember: this product is an accessory for LED bulbs, not a complete headlight assembly; confirm H7 fit and available housing space before ordering.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Will this work with HID systems?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: No. The Xprite H7 Canbus decoder is designed for LED bulbs only and is not compatible with HID ballast systems.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Do I need to splice wires to install it?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: No splicing is required; the unit is plug-and-play, connecting inline between the vehicle harness and H7 LED bulb.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"Xprite","offers":[{"title":"Default Title","offer_id":55167183618391,"sku":"B0CNTCKKN3","price":38.44,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1050\/1524\/7191\/files\/xprite-h7-harness-front-view.jpg?v=1790377567","url":"https:\/\/britishgarage.co.uk\/products\/xprite-h7-canbus-decoder-harness-pack-of-2-anti-flicker-error-free-plug-and-play","provider":"British Garage","version":"1.0","type":"link"}